Hex Set Screws are fully threaded with a hexagon head if you require an unthreaded section (called shank) then you need to search for a hex bolt. Hex set screws are often threaded into something such as a piece of machinery rather than being used with a nut Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. Most products can be identified by the following markings: A2 A2-70 304 or G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material Grade v Class Difference: Imperial fastenings are referred to as grades and metric fastenings are referred to as classes. Both have marking systems that make it possible to determine grade and class. An example is a ½” UNC bolt with 5 lines on the head is grade 8 and 3 lines is grade 5 both are regarded as high tensile. Metric bolts are slightly different if it has 4.6 then it is mild steel and 8.8 is high tensile. The markings on a stainless fastener indicate the grade of material and strength e.g. material G304 grade will have one of the following markings: A2-70 G304 A2 304 and G316 grade stainless will have one of the following: A4-70 G316 A4 316 Thread Pitch (Metric): Pitch means the distance between the peaks of two threads along a screw bolt or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm Fastener length: is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person and Bolt and Nut Australia is not responsible for any loss claim or damages arising therefrom.
Hex Set Screws are fully threaded with a hexagon head if you require an unthreaded section (called shank) then you need to search for a hex bolt. Hex set screws are often threaded into something such as a piece of machinery rather than being used with a nut Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. Most products can be identified by the following markings: A2 A2-70 304 or G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material Grade v Class Difference: Imperial fastenings are referred to as grades and metric fastenings are referred to as classes. Both have marking systems that make it possible to determine grade and class. An example is a ½” UNC bolt with 5 lines on the head is grade 8 and 3 lines is grade 5 both are regarded as high tensile. Metric bolts are slightly different if it has 4.6 then it is mild steel and 8.8 is high tensile. The markings on a stainless fastener indicate the grade of material and strength e.g. material G304 grade will have one of the following markings: A2-70 G304 A2 304 and G316 grade stainless will have one of the following: A4-70 G316 A4 316 Thread Pitch (Metric): Pitch means the distance between the peaks of two threads along a screw bolt or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm Fastener length: is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person and Bolt and Nut Australia is not responsible for any loss claim or damages arising therefrom.
Hex Set Screws are fully threaded with a hexagon head if you require an unthreaded section (called shank) then you need to search for a hex bolt. Hex set screws are often threaded into something such as a piece of machinery rather than being used with a nut Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. Most products can be identified by the following markings: A2 A2-70 304 or G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material Grade v Class Difference: Imperial fastenings are referred to as grades and metric fastenings are referred to as classes. Both have marking systems that make it possible to determine grade and class. An example is a ½” UNC bolt with 5 lines on the head is grade 8 and 3 lines is grade 5 both are regarded as high tensile. Metric bolts are slightly different if it has 4.6 then it is mild steel and 8.8 is high tensile. The markings on a stainless fastener indicate the grade of material and strength e.g. material G304 grade will have one of the following markings: A2-70 G304 A2 304 and G316 grade stainless will have one of the following: A4-70 G316 A4 316 Thread Pitch (Metric): Pitch means the distance between the peaks of two threads along a screw bolt or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm Fastener length: is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person and Bolt and Nut Australia is not responsible for any loss claim or damages arising therefrom.
Hex Set Screws are fully threaded with a hexagon head if you require an unthreaded section (called shank) then you need to search for a hex bolt. Hex set screws are often threaded into something such as a piece of machinery rather than being used with a nut Material / Coating: Stainless Steel A2-70 G304 is the most popular grade of stainless steel. It is aesthetically pleasing to the eye and very practical because of its excellent corrosion protection in most environments. Most products can be identified by the following markings: A2 A2-70 304 or G304. Stainless steels are largely non-magnetic but it is common for stainless steel fasteners to show a small degree of magnetism which is a result of work-hardening during the manufacturing process Can Stainless corrode?: Stainless steel is corrosion-resistant but not corrosion-proof and corrosion can occur if the material is installed or handled incorrectly. The use of tools and drills made from conventional steel during the installation of stainless steel fasteners may also lead to problems. Even the hardest of tools can produce debris that leaves minute steel particles on the stainless steel fastener surfaces or in pre-drilled holes. It is these particles that often rust when exposed to moisture or oxygen and can result in a stained or tarnished finish to the stainless steel material Grade v Class Difference: Imperial fastenings are referred to as grades and metric fastenings are referred to as classes. Both have marking systems that make it possible to determine grade and class. An example is a ½” UNC bolt with 5 lines on the head is grade 8 and 3 lines is grade 5 both are regarded as high tensile. Metric bolts are slightly different if it has 4.6 then it is mild steel and 8.8 is high tensile. The markings on a stainless fastener indicate the grade of material and strength e.g. material G304 grade will have one of the following markings: A2-70 G304 A2 304 and G316 grade stainless will have one of the following: A4-70 G316 A4 316 Thread Pitch (Metric): Pitch means the distance between the peaks of two threads along a screw bolt or fastener expressed in millimetres (mm). Used when referring to Metric parts. For example a thread pitch of 1.50mm means that the distance between one thread and the next is 1.50mm Fastener length: is generally measured from the point where the surface of the material will be when the fastener is installed to the end of the fastener. All material is advisory only and its use by anyone is entirely voluntary. Reliance on it for any purpose by anyone is at the sole risk of that person and Bolt and Nut Australia is not responsible for any loss claim or damages arising therefrom.
Last updated at 04/11/2026 13:04:50
M8 x 1.25p x 140mm Part Thread Metric Coarse Hex Bolt A2-70 Stainless G304 DIN 931
Free delivery between Tue – Thu
Qty 1 Hex Bolt M8 X 140mm Metric Coarse Part Thread A2-70 Stainless
Free delivery
Affiliate Disclosure: We may receive a small commission for purchases made through this link at no extra cost to you. This helps support our site. Thank you!
M8 x 1.25p x 140mm Part Thread Metric Coarse Hex Bolt A2-70 Stainless G304 DIN 931
Free delivery between Tue – Thu
Qty 1 Hex Bolt M8 X 140mm Metric Coarse Part Thread A2-70 Stainless
Free delivery
Affiliate Disclosure: We may receive a small commission for purchases made through this link at no extra cost to you. This helps support our site. Thank you!
